Frustrating day at the office
-
- Member
- Posts: 169
- Joined: December 9th, 2003, 1:00 pm
- Enter the middle number please (3): 5
- Location: Vancouver,WA.
- Contact:
Had a combo break with one leg(1/2 inch long) I couldn't get to fill. After exhausting all options I drilled the tip and popped a perfect bullseye. Attempted to fill, came back couple minutes later expecting to see it filled and it still appeared the same. This is the second time in three weeks this has happened. I'd sure like to prevent this problem from happening again and save myself the embarrassment of succumbing to a less than high quality repair I expect for my customers. Delta resins and injectors.
-
- Senior Member
- Posts: 3192
- Joined: February 25th, 2004, 1:44 pm
- Enter the middle number please (3): 5
- Location: uk Lincolnshire
- Contact:
Frustrating day at the office
Is there any way you are confusing air with moisture, It seems unlikely a leg will not fill when drilled and popped.
Moisture in the leg when viewed from diffrent angles can look like air to the less experienced tech.
Moisture is our biggest enemy in screen repair.
Moisture in the leg when viewed from diffrent angles can look like air to the less experienced tech.
Moisture is our biggest enemy in screen repair.
33,000 + screen repairs over 18 years and still learning.
Over
Over
Tent set up
You've tried crack expander, probing the area both inside and out, or heat? But this is only a 1/2" leg. Hmmm...
Two questions. Did your pit filler pull off the glass while lifting the curing tab, and did your popped bullseye clear while leaving the crack still visable?
Sounds exactly like Rain X or similar contamination. The break is filled properly, but the resin cannot make total contact with the glass, leaving it visable. These repairs will fail and are not your fault. I mark the invoice with "Rain X or similar contamination" and expect to be paid. Of course, give the money back when it fails.
See the recent post about large pits. Many knowledgeable posts about how to treat the surface to allow the resin to adhere, but not a word about the inside surfaces of the break. If it won't adhere to the outside, it won't on the inside, either.
Hope this helps.
Sounds exactly like Rain X or similar contamination. The break is filled properly, but the resin cannot make total contact with the glass, leaving it visable. These repairs will fail and are not your fault. I mark the invoice with "Rain X or similar contamination" and expect to be paid. Of course, give the money back when it fails.
See the recent post about large pits. Many knowledgeable posts about how to treat the surface to allow the resin to adhere, but not a word about the inside surfaces of the break. If it won't adhere to the outside, it won't on the inside, either.
Hope this helps.
-
- Member
- Posts: 169
- Joined: December 9th, 2003, 1:00 pm
- Enter the middle number please (3): 5
- Location: Vancouver,WA.
- Contact:
Just wanted to answer a couple questions posed:
1)living in the northwest, moisture is almost always a concern. I didn't use the moisture evaporator because the outside window temp was 85 degrees and we haven't had rain for a week. Maybe I shouldn't be so quick to jump to conclusions.
2) Bill, no rain-x apparent on glass but bull did fill leaving the leg still visible.
Thanks all for your suggestions, Steve,
1)living in the northwest, moisture is almost always a concern. I didn't use the moisture evaporator because the outside window temp was 85 degrees and we haven't had rain for a week. Maybe I shouldn't be so quick to jump to conclusions.
2) Bill, no rain-x apparent on glass but bull did fill leaving the leg still visible.
Thanks all for your suggestions, Steve,
-
- Senior Member
- Posts: 3192
- Joined: February 25th, 2004, 1:44 pm
- Enter the middle number please (3): 5
- Location: uk Lincolnshire
- Contact:
It may not have rained but did the customer wash his car or use the screen washers.
It is very important to learn how to recognise moisture in a chip or crack, this is something I find easy to show when training but find it difficult to put into words.
Do you have a lot of people over there using Rainx it is not something I have found a problem with in the UK.
In a bullseye with leg or starbreak there will always be moisture in the legs long after the main body has dried out.
Keep posting.
It is very important to learn how to recognise moisture in a chip or crack, this is something I find easy to show when training but find it difficult to put into words.
Do you have a lot of people over there using Rainx it is not something I have found a problem with in the UK.
In a bullseye with leg or starbreak there will always be moisture in the legs long after the main body has dried out.
Keep posting.
33,000 + screen repairs over 18 years and still learning.
Over
Over
-
- Member
- Posts: 169
- Joined: December 9th, 2003, 1:00 pm
- Enter the middle number please (3): 5
- Location: Vancouver,WA.
- Contact:
Training Class in Houston
Screenman, RainX is everywhere over here. I've personally been asking my customers their experiences positive and negative. Responses are about 50/50 like/dislike. Personally, I think I've found something that lasts longer and doesn't interfere with Delta resins that I'm starting to offer as a service as the rainy months arrive.
-
- Senior Member
- Posts: 733
- Joined: November 13th, 2003, 9:24 am
- Contact:
Who is online
Users browsing this forum: Google [Bot] and 5 guests